History of Flight
On May 10, 2023, at 0749 Pacific daylight time, a Gates Lear Jet 36A, registration N56PA, was destroyed when it was involved in an accident near San Clemente Island, California. Both pilots and the additional crewmember were fatally injured. The airplane was operating as a Title 14 Code of Federal Regulations Part 91, other work use flight.
The airplane departed Point Mugu Naval Air Station (NTD), Oxnard, California, about 0723 as the lead airplane in a formation with a second Lear Jet, using callsigns FENIX01 (N56PA) and FENIX02 (N544PA). The purpose of the flight was to participate in training exercises with the United States Navy in Warning Area 291 (W291). The flight proceeded south towards San Clemente Island with FENIX02 flying in formation with FENIX01.
About 0740, after entering W291 at 15,000 ft msl, FENIX02 (positioned on the right side of FENIX01) observed FENIX01’s flaps partially deploy. They asked the pilots of FENIX01 if they had deployed flaps, and they replied that they didn’t think so. FENIX02 then observed the flaps retract and seconds later observed white or gray colored smoke coming from the left, aft side of the airplane.
FENIX02 notified FENIX01 of the smoke and FENIX01 responded that they detected an odor in the cabin. At this point, the aircrew of FENIX02 believed FENIX01 was no longer flying on autopilot because the airplane was “lightly rocking and pitching.” FENIX02 then observed pink fluid coming from the tail section of the airplane and informed FENIX01 that they had a hydraulic leak.
FENIX02 then observed flames coming from around the aft equipment bay access door and told FENIX01 that they were on fire. At 0740:30, FENIX01 started a left, descending turn and declared an emergency with the Navy area controller at 0741:00. They stated their intentions to land at San Clemente Island Naval Auxiliary Landing Field (NUC), which was about 32 miles north of their position. Shortly thereafter, FENIX02 observed the drag chute, mounted on the aft equipment bay access door, depart from FENIX01. FENIX02 then took over as the lead airplane for the formation and maneuvered in front of FENIX01. FENIX01 was last observed passing underneath FENIX02 from the left to right side as they descended between 9,000 and 7,000 feet msl. No additional radio transmissions were heard from FENIX01 from that point. According to the captain of FENIX02, there was an overcast marine layer of clouds below them from about 2,000 ft to 4,000 ft msl that obscured most of San Clemente Island and NUC.
FENIX01 subsequently made a series of right-hand descending turns, during which the Digital Electronic Engine Control (DEEC) incident recorder recorded several additional faults between about 0745:43 and when the DEEC data ended about 0746:32 following indications of a loss of power to the DEEC. The last recorded ADS-B data point at 0749:11 showed the airplane at 1,338 ft and heading northwest about ½ mile off the southwest side of San Clemente Island, about 4 miles southeast of where the airplane’s wreckage was later located.
Wreckage and Impact Information
The airplane wreckage was located in the Pacific Ocean about 13 miles south of NUC and about 1.5 miles west of San Clemente Island at a depth of about 300 ft. The identified wreckage debris field was surveyed using sonar equipment and remotely operated vehicles (ROV). The debris field extended several hundred feet along the ocean floor in a northwest direction. A portion of the airplane was able to be recovered in October 2023.
Investigators examined the wreckage two different times. The wreckage was fragmented and exhibited corrosion consistent with saltwater immersion. It was estimated that about 40% of the airplane was recovered. The identifiable wreckage included portions of the nose cone, cockpit instrument panel, cabin floorboard, portions of both wings, both engines and nacelles, some components from the aft equipment bay, and the vertical stabilizer and left horizontal stabilizer. Impact damage and a lack of complete wreckage prevented verification of flight control continuity.
Main hydraulic system components consisting of the hydraulic reservoir, accumulator, pressure filter, return filter, and auxiliary hydraulic pump were identified and examined. The input ports of both left and right hydraulic shut off valves that were attached to the hydraulic reservoir were probed and found that the left valve was in the closed position and the right valve was in the open position. The flap control valve was not located.
Both engines were separated from the airplane structure when examined. Both engines’ fan blades and first stage compressor blades exhibited bending opposite of rotation. Neither engine was able to rotate to verify internal continuity, and both engines exhibited corrosion degradation. No mechanical anomalies were noted with either engine during examination.
The left fuel motive flow line was intact from the fuel pump up to the fuselage fitting, where the line normally passes through the fuselage skin into the aft equipment bay near the aft left engine mount. The fuselage fitting on the aft equipment bay side did not have a b-nut attached nor the line that should connect the fitting to the motive flow valve. The left engine hydraulic pressure line and inlet total pressure (PT2) line, which pass through the fuselage into the aft equipment bay adjacent to the motive fuel line, each had aluminum b-nuts present on the interior side of their respective fuselage fittings, and the interior lines for each was sheared at the fitting.
The left fuel motive flow fuselage fitting and the hydraulic fluid return fitting were examined. Both were steel bulkhead type fittings, and both fittings were corroded. No thermal damage was observed on the outboard nuts and attached portions of tubing. On the inboard side, the motive flow fitting was missing the aluminum nut and tubing. Examination of the threads on the inboard side of the motive flow fitting did not exhibit evidence of thread stripping. The hydraulic fluid return fitting still had the aluminum nut attached on the inboard side, and the aluminum tubing had sheared at the nut face. According to the operator, there was no record of maintenance being performed on the motive flow fitting and b-nut since the airplane had been assembled.
Portions of the wreckage exhibited exposure to heat and fire.
Additional Information
The left and right engine DEECs are installed adjacent to each other in the upper, left side of the aft equipment bay, aft of the left engine pylon. A single DEEC, from the left engine, was recovered during examination of the wreckage. The DEEC included an incident recorder which collects parameters in non-volatile memory. Data from the accident flight was recovered. The data recorded 5,120 seconds of data (about 85 minutes), including the cruise, descent, and landing from the flight before the accident and the full data recorded from the accident flight.
At time stamp 50 seconds through the remainder of the dataset, the N2 and PLA parameters indicate N2 Signal Fail and No Valid Data respectively. This coincides with faults indicating a failure of the FCU PLA circuit and the N2 Monopole Circuit being open or shorted consistent with damaged wiring. Per system design, the DEEC reverted to manual mode.
Data recovered from the incident recorder associated with the accident flight was correlated with ADS-B data. The DEEC recorded the first fault about 0741:46, and the incident recorder data subsequently ends about 0746:32.
Fire Damage
Fire and heat damage was concentrated in the vicinity of the aft equipment bay (tail cone), aft portion of the fuselage fuel tank, both wheel-well areas, and the inboard section of both flaps. The right side of the aft equipment bay fuselage structure had heat/fire damage. The left side of the equipment bay and the entire fuselage structure aft of the avionics bay was not recovered.
The upper left side of the fuselage fuel tank aft bulkhead exhibited a region of damage that was mostly devoid of any remaining charred primer paint, and the aluminum substrate was eroded. In some areas, the erosion was all the way through the thickness of the aluminum bulkhead panel. Other areas throughout the entire fuselage fuel tank aft bulkhead that exhibited charred or missing paint did not exhibit the erosion.
The fuselage fuel tank was fragmented, with portions of the fuel bladder material attached to the aft pressure bulkhead, fuel tank divider panels, and fuel tank aft bulkhead. The fuselage fuel tank aft area bladder portions exhibited heat damage. The forward section of the fuselage fuel tank that contacted the pressure bulkhead had no heat damage. Soot deposits were found on the fuselage fuel tank fuel quantity indicator tube.
Examination of the left and right rear engine beams showed an asymmetric material condition between the two. The left engine beam exhibited beam deformation, extreme thinning of the upper beam plate, moderate thinning of the forward plate, and unpainted surfaces with corrosive deposits. The thinning of the left engine beam plates presented an eroded appearance similar to what was observed on the upper left portion of the fuselage fuel tank aft bulkhead.
The hydraulic reservoir tank is mounted on the forward, right interior side of the aft equipment bay. The quadrant of the tank that faced inward to the equipment bay compartment exhibited substantial heat damage, while the side that was up against the fuselage and the quadrant that faced aft was undamaged by heat.
The generator control panel, which would have been installed on the left side of the aft equipment bay adjacent to the access door, exhibited thermal damage and charring. More severe thermal damage was evident on the forward section of the panel.
The airplane was equipped with under wing external stores hardpoints, a Reeling Machine Target Tow System, and other underwing stores (Mission Equipment). Power for the Mission Equipment originates from the airplane generator control box in the aft equipment bay. The mission equipment power cables were traced from the J-Box to a location in the aft equipment bay a few inches from the contactor. There was no evidence of arcing or melting of the power cables that would be indicative of them being energized. The equipment and wire bundles in the J-box were undamaged by fire and exhibited no evidence of arcing.
There was evidence of fire damage to portions of airframe and mission wire bundles that were outside the pressurized fuselage in the wheel well area. The entire wheel well area, including the main landing gear tires and wheels, had evidence of fire damage with black soot, heat deformed metal, and burned and melted wiring insulation. The current limiter, contactor, and the mission wiring that connects the generator control box to the current limiter and the contactor was not located within the wreckage.